Chappell Supply of Texas

HSE Series

Portable - Electric Driven

Value and dependability both describe these units.  Small units that deliver big results. 

Looking for quiet operation and low vibration?  These electric hot water washers are ideal for industrial applications.

 

HSE-1502-0M10 Pressure Washer

HSE-3504-0M10 Pressure Washer

HSE-1502-0M10

HSE-3504-0M10

 

Features for HSE-1002,1502, 2003:

  1. Energy efficient top-fired, dual spiral coil with powder coated heat exchanger

  2. No. 1 or No. 2 diesel or kerosene fired burner

  3. Complete system diagnostic board

  4. Totally enclosed fan-cooled electric motor with manual thermal overload protection

  5. Racor fuel filter/water separator

  6. Polyethylene burner fuel tank                                                               

  7. Direct drive triplex piston pump with ceramic plungers and forged brass manifold

  8. Thermal relief valve

  9. Stainless-steel and brass unloader valve

  10. Float tank (N/A on HSE-1002-0M11)

  11. High pressure detergent injection (low pressure on HSE-1002-0M11)

  12. Pressure and high limit safety controls

  13. Reinforced powder coated steel tube frame

  14. Powder coated center balanced lifting hook

  15. Electric cord hanger

  16. 35 foot power cord with ground fault circuit interrupter (GFCI)

  17. Hose real mounting bracket

  18. Pneumatic tires with tubes (4)

  19. Solid steel threaded axles

  20. Wand holder

  21. 3/8 inch x 50 foot steel wire-braided pressure hose with screw connects, swivel and bend restrictors

  22. Professional-grade insulated trigger gun with safety lock-off

  23. Adjustable pressure insulated dual lance with 15-degree fixed and detergent nozzles

Additional features:

  • Temperature rise 150ºF/66ºC maximum above ambient

  • Easy coil drain

  • Solid state electronic ignition

  • Water output temperature is approximately 190º to 200º (All models except  HSE-1002-SM10)

  • Water output temperature for "wet" steam is approximately 250º (HSE-1002-SM10 only)

  • Operates at 650 PSI in steam mode (HSE-1002-SM10 only)

  • Locking tire break

    •

    CSA certification stamp CETA certification stamp

    Burner Design

    1. Large capacity exhaust tube allow proper exhausting of combustion gases.

    2. When troubleshooting a burner problem the spark can easily be checked within seconds through the convenient sight glass

    3. Continuous wrap tubing coil eliminated butt welds which can cause leaks.  The coil is lightweight  and designed for easy replacement.

    4. The insulation pad is designed for easy replacement and durability.

    5. Coil inlet/outlet connections with convenient coil drain, allows for easy draining of all water in coil to prevent  freezing.

    6. The combustion chamber drain allows for easy draining of water or fuel build-up.

    7. Incoming air flows between outside wrap and inner wrap eliminating the need for coil insulation.

    8. Single wire braided fuel hose prevents leakage, protects the system and won't crack or kink.

    9. Electrodes are self-gapping for proper ignition and combustion.

     
    Burner Design diagram

    Warranty Information

    One (1) year limited parts and labor warranty.

    Three (3) year limited warranty on coil.

    Five (5) year limited warranty on pump.

     

     

    * Note:  Unit Dim. (L x W x H)   34" x 29" x 33"*

    * HSE-1002-SM10  Combination Steam Cleaner/Pressure Washer*

    All have General Pumps

    Shipping weight between  368  lbs.  &  393  lbs.

     Net weight between  245  lbs.  &  270  lbs.

     
    Model # PSI GPM HP Voltage/ Phase/ Amp Burner Tank Cap  (gal) Burner Cons (gph)
    HSE-1002-0M11 1000 2.0 1.5 120V/1Ø/15.0 4.0 1.33
    HSE-1002-0M10 1000 2.0 1.5 120V/1Ø/15.0 4.0 1.33
    HSE-1002-SM10 1000 2.0 1.5 120V/1Ø/15.0 4.0 1.33
    HSE-1502-0M10 1500 2.0 2.0 120V/1Ø/19.0 4.0 1.33
    HSE-2003-0M10 2000 2.8 4.0 230V/1Ø/18.0 4.0 1.48
    Options:
    Auto start/stop   (HX-0050 for HSE-1002/1502-0M10)
    Auto start/stop-steam   (HX-0052 for HSE-1002/1502-0M10)    (HX-0054 for HSE-2003)
    Auto start/stop-CAD cell  (HX-0055 for HSE-1002/1502-0M10)   (HX-0056 for HSE-2003)
    Auto start/stop-steam-CAD cell   (HX-0057 for HSE-1002-0M10)   (HX-0058 for HSE-1502)    (HX-0059 for HSE-2003)

     

    HSE-2504, 3004, 3504

    HSE 3504 Pressure Washer

     

    Features for HSE-2504, 3004, 3504:

    1. Energy efficient top-fired, dual spiral coil with powder coated heat exchanger

    2. No. 1 or No. 2 diesel or kerosene fired burner

    3. Complete system diagnostic board

    4. Totally enclosed fan-cooled electric motor with manual thermal overload protection

    5. Electric cord hanger

    6. Stainless-steel and brass unloader valve                                                               

    7. Thermal relief valve

    8. Belt drive triplex piston pump with ceramic plungers and forged brass manifold

    9. High pressure detergent injection

    10. Polyethylene burner fuel tank

    11. Racor fuel filter/water separator

    12. Float tank

    13. 35 foot power cord (GFCI on HSE-2504-0M10)

    14. 3/8 inch x 50 foot steel wire-braided pressure hose with screw connects, swivel and bend restrictors

    15. Professional-grade insulated trigger gun with safety lock-off

    16. Adjustable pressure insulated dual lance with 15-degree fixed and detergent nozzles

    17. Wand holder

    18. Center balanced lifting hook

    19. Reinforced powder coated steel tube frame

    20. Easy coil drain

    21. Pneumatic tires with tube (4)

    22. Solid steel threaded axles

    23. Locking tire brake

     

    Additional features:

  • Temperature rise 150ºF/66ºC maximum above ambient

  • Pressure and high limit safety controls

  • Solid state electronic ignition

    •

     

    Warranty Information

    One (1) year limited parts and labor warranty.

    Three (3) year limited warranty on coil.

    Five (5) year limited warranty on pump.

    CSA certification stamp

    CETA certification stamp

     

     

    * Note:  Unit Dim. (L x W x H)   49.5" x 28" x 40.5"*

    All have General Pumps

    Shipping weight between  688  lbs.  &  761  lbs.

    Net weight between  558  lbs.  &  631  lbs.

     
    Model # PSI GPM HP Voltage/ Phase/ Amp Burner Tank Cap  (gal) Burner Cons (gph)
    HSE-2504-0M10 2500 3.2 6.0 208-230V/1Ø/25.0 10.0 2.1
    HSE-2504-0M30 2500 3.2 6.0 208-230V/3Ø/16.0 10.0 2.1
    HSE-3004-0M10 3000 3.5 8.0 208-230V/1Ø/36.0 10.0 2.1
    HSE-3004-0M30 3000 3.5 8.0 208-230V/3Ø/24.0 10.0 2.1
    HSE-3504-0M10 3500 3.3 10.0 208-230V/1Ø/39.0 10.0 2.1
    HSE-3504-0M30 3500 3.3 10.0 208-230V/3Ø/28.0 10.0 2.1

     Options:
    Auto start/stop (HX-0070)
    Skid feet (HX-0088)
    Hour meter (HX-0049)
    Auto start/stop (HX-0050 for HSE-1002/1502-0M10)
                Auto start/stop-steam   (HX-0071 for HSE-2504)   (HX-0072 fits HSE-3004)   (HX-0073 for HSE-3504)
    Auto start/stop-CAD cell (HX-0074)
              Auto start/stop-steam-CAD cell    (HX-0075 for HSE-2504)   (HX-0076 for HSE-3004)   (HX-0077 for HSE-3504)

    Chappell Supply of Texas Site Map

     

    For more information call 1-877-439-8500

     

    Biological Wastewater Treatment Pressure Washers Water Recycling Systems
    Aqueous Parts Washers Explosion-Proof Pressure Cleaning System Heavy Duty Industrial Cleaning Systems
    Water Cannon System Mosmatic Corp. Pump Index Latimat Containment System
    Hose Product Line Industrial Steam Cleaning Tanks & Tank Accessories
    Return to Chappell Supply of Texas Main Page

     

    Chappell Supply of Texas

    1-877-439-8500

    548 S Saginaw Blvd

    Saginaw, TX  76179

           Phone: 817-439-2200      Fax:  817-439-2400

             email:   info@chappellsupplyoftexas.com

     
       

    Site Hosted by:            Internet Techs.net